Home/Products/Solid bumper for iPhone 15 Pro Max
Smooth Our pursuit of usability
Experimenting over and over again we designed this bumper is to have no uncomfortable
feeling between the bumper and the finger.It is also possible to use the swipe smoothly.
Compatible with the iPhone 15 series' USB Type C port,
the opening was kept large at 7mm height (3.5mm corner radius)
and 16mm width to accommodate all kinds of cables.
(Dimensions of 6.5mm height,
3.25mm corner radius for iPhone 15 only)
 Inner dimensions of the screen opening were increased to
accommodate many commercially available screen protectors.

[Inner dimensions for bumper case front opening]
●Bumper for iPhone 15: width 68mm, height 144mm
●Bumper for iPhone 15 Pro: width 66.7mm, height 142.7mm
●Bumper for iPhone 15 Pro Max: width 73mm, height 156.2mm
An optional feature is the camera lens guard bar, which is machined from duralumin.
You can choose and customize how your camera lens is protected.
Even when placed directly on a flat surface, the camera lens does not touch the surface.
Another optional feature is the camera lens guard,
machined from duralumin.
Protect the all-important camera lens.
Its shape has been carefully designed to prevent
interference with the LiDAR sensor and camera flash.
We used Nitto Denko’s strong
double-sided tape to affix the lens guard.
It leaves little residue when removed, keeping your iPhone clean. 		Besides the original Apple MagSafe charger,
many third-party MagSafe accessories
are compatible with the bumper.
(Shown here is a MOFT magnetic card holder)

[Inner dimensions of rear opening]
●iPhone 15：height 142.5mm, width 65mm
●iPhone 15 pro：height 141.5mm, width 64mm
●iPhone 15 Pro Max：height 155mm, width 70.4mm
Our iPhone cases also come equipped with a strap hole.
The strap is connected on the bottom left of the phone,
so it will not interfere with the mouthpiece
during phone conversations.
The cases can also be easily stored in your pocket.		 The bumper does not block the antenna module.
There are openings to accommodate each module,
allowing you to use 5G seamlessly.
Rubber o rings are attached to prevent the screws from losing. The separately sold color bolt set (model number: GI-305)
can also be used for the iPhone 15 series cases,
as the bolt size is the same.
※Please note that if you use the aluminum shim to avoid lens contact,
the length of the bolts will not be sufficient,
and therefore, it cannot be used.
Regarding the Qi wireless charge
It is possible to charge with a Qi wireless charger while using a Solid bumper case (*1)
It will not charge when using a Solid case or an aluminum back panel.
( Please charge with the genuine USB-C cable attached with the iPhone)
Regarding the WIFI、3G、4G、Bluetooth、GPS、NFC, etc.
(When an aluminum panel is attached the conditions are the same as the Solid case. )
Face ID → There are no problems while using face recognition and unlocking.
Apple Pay → There are no problem using wifi for both Solid bumper and Solid case. *2
Wifi → There are no problem using wifi for both Solid bumper and Solid case. *2
5G → There are no problem using 4G for both Solid bumper and Solid case. *2
4G → There are no problem using 4G for both Solid bumper and Solid case. *2
Bluetooth → There are no problem using Bluetooth for both Solid bumper and Solid case. *2
GPS → There are no problem using GPS for both Solid bumper and Solid case. *2
Magsafe → There are no problem using GPS for both Solid bumper and Solid case. *2
*1 Using the Qi wireless charger while the case is attached has the possibilities to lower
the charge efficiency due to the 1.5mm thickness of the case that makes a gap between
the wireless charger and the iPhone. Also, there will be a difference on
the charging time depending on the output wattage and the voltage of the adapter the Qi wireless charger.

*2 This product is made of Duralumin, which interrupts the signal from the back of the iPhone.
It is possible that might lower the phone reception.
Using the case in places with a poor reception in the first place can lower the reception of the signal even more. However, there are no problems in places with a good reception.
Color variations
Silver Black
Red Matte Gray
Matte Titanium Matte Blue
【Size,Weight】
11×82×165.8mm / 20g

【Included】
Solid bumper 1set、
Screw 5 pieces(Includes one spare)
Shock absorber 10pieces(Includes two spare)、
Oring 5 pieces(Includes one spare)

【Lens Anti-Touch Kit】 (Packed separately)
7.5-mm Torx screw x 3 pieces (including 1 spare)
2-mm aluminum shim x 3 pieces (including 1 spare)
1-mm aluminum shim x 3 pieces (including 1 spare)
Colors
Please place your order after reading and agreeing with the notes below.

■Due to a tremendous amount of orders it might take 1 to 2 months before we ship the item.

■Your order will be shipped as soon as the product is made.
Lens guard for iPhone 15 pro / 15 Pro Max
Protect the all-important camera lens.
Its shape has been carefully designed to prevent interference with the LiDAR sensor and camera flash.
Nitto Denko’s strong double-sided tape was used to affix the lens guard.
It leaves little residue when removed, keeping your iPhone clean.
Lens guard【Square】for 15 Pro / 15 Pro max
(Color:Silver)
 Lens guard【Square】for 15 Pro / 15 Pro max
(Color:Black)
Colors
Colors
Lens guard【Triangle】for 15 Pro / 15 Pro Max
(Color:Silver)
 Lens guard【Triangle】for 15 Pro / 15 Pro Max
(Color:Black)
Colors
Colors
Lens Guard Bar for iPhone 15 series
We have prepared a lens guard bar for iPhone 15 series, whose lens protrudes greatly.
When placed on a flat surface, the lens will not interfere.
(When using the lens guard bar in conjunction with the lens guard, the lens guard will contact first.)

【Please note】
It is not possible to use in conjunction with aluminum color bolts due to insufficient bolt length.
lens guard bar for iPhone 15 Pro Max / 15 Plus / 14 Pro Max / 14 Plus
(Color:Silver,Black)
Color
Screen protectors for the iPhone 15 series
Inner dimensions of the front opening for GILD Design’s iPhone 15 Series bumper are as follows.

●Bumper for iPhone 15: width 68mm, height 144mm
●Bumper for iPhone 15 Pro: width 66.7mm, height 142.7mm
●Bumper for iPhone 15 Pro Max：width 73mm, height 156.2mm

We improved our existing bumpers by increasing the inside width to accommodate more accessories.
You can use screen protectors with width less than the inside width.

[Warning]
Due to shape limitations, we cannot guarantee compatibility with all screen protectors
even if their width is less than the inside width of the bumper.
We recommend the following screen protector.
Round edge crystal armor for iPhone 15 Pro Max

Product no：43455
Product code：GI34-33F
Price：2,710 yen
Size：71.7×154.8×0.33mm
Aluminum color screw set
Colors
※If you choose to use aluminum shims to avoid touching the lens,
the color bolts cannot be used as they are not long enough.
Please place your order after reading and agreeing with the notes below.

■Due to a tremendous amount of orders it might take 1 to 2 months before we ship the item.

■Your order will be shipped as soon as the product is made.
Regarding postage

*For DHL
If the total value of your order is 11,999 yen or less, you will be charged 2,500 yen for shipping.
If the total value of your order is 12,000 yen or more, you will be charged 1,500 yen for shipping.


Please be sure to add your phone number on PayPal when using DHL Priority shipping.
We cannot process the shipping if this information is not included on the invoice.
Please place your order after reading and agreeing with the notes below.

Please read carefully the following before making an order.

We will send a notification regarding the date of delivery individually by email.

The shipment will be in the order as we received them. However, Order colors, and mixed color cases will take time to prepare, this might change the shipping order.

Before making an order please be sure to set your mail to receive messages from info@gilddesign.com.

When the order is complete an auto reply message will be send to you. If you cannot receive the message, please contact info@gilddesign.com after setting the domain.
Warning
・Please understand that we are not responsible for any breakage, or damage that may be caused by actions that were not suggested in this instruction.

・This product is made of Duralumin, which interrupts the signal from the back of the iPhone. It is possible that might lower the phone reception.

・This product is anodized. There are two dots that were not anodized on the inside of the case. These are the electrical connection places that will not catch the color during the anodizing process, and it is not a defect.

・This product is designed for iPhone 15 Pro Max.

・This product is not made to protect the iPhone 15 Pro Max completely from all kinds of damage. Please notice that we will not be responsible for any breakage, loss, damage, or data loss of the iPhone.

・By using silicone shock absorber sheets, our product is designed to prevent the iPhone and the aluminum case from touching each other, and it is not designed to protect the iPhone from all damage.

・Please be aware that our company will not be responsible for any scratches on your iPhone when using the case.

・We might make changes on the case functions, appearance, or package contents without giving a notice.

・This case is made of aluminum. Please be careful on the sharp edges when installing the case.

・After putting the wrench firmly into the screw, please fasten it with the right amount of force to prevent the screw from breaking.

・Please note that as the characteristics of anodizing, it is difficult to produce the same color. There are possibilities that color differs from the image due to the production lot.
※iPhone.iPad are trademarks of Apple Inc.
※The trademark'iPhone'is used with a license from Aiphone K.K.