Home/Products/Solid bumper for iPhone 14 Pro Max
Smooth Our pursuit of usability
Experimenting over and over again we designed this bumper is to have no uncomfortable
feeling between the bumper and the finger.
It is also possible to use the swipe smoothly.
The bumper for the iPhone 14 Pro model has a wider opening for the screen compared to previous bumpers,
allowing for the use of many commercially available protective glass films.
(The dimensions for the protective glass film installation on the 14 Pro bumper are 68mm in width and 144.1mm in height)
(The dimensions for the protective glass film installation on the 14 Pro Max bumper are 73.5mm in width and 156.6mm in height)
As a new option, we have prepared a lens guard bar. (Only for 14 Pro / 14 Pro Max) You can choose the lens protection method according to your TPO. If it is a flat place, the lens may not come into contact even if you place it directly. As an option, we have also prepared a tungsten steel cut-out lens guard for the "iPhone 14/14 Plus" and "14 Pro/14 Pro Max," which was well received for the iPhone 13 series. This will allow you to protect your valuable lens.
Not only Apple's original MagSafe charger, but also many third-party MagSafe accessories can be mounted on the iPhone body without interference with the bumper. (The bumper in the image is for the iPhone 14 Pro) (The accessory in the image is a MOFT card holder) Included in the package are aluminum shims and longer bolts (7.5mm) that can eliminate tilt when placed on a flat surface. Please use them according to your situation. (Note: Shims and bolts alone cannot prevent lens interference)
Our iPhone cases also come equipped with a strap hole.
The strap is connected on the bottom left of the phone,
so it will not interfere with the mouthpiece during phone conversations.
The cases can also be easily stored in your pocket.		 The bumper does not block the antenna module.
There are openings to accommodate each module,
allowing you to use 5G seamlessly.
Rubber o rings are attached to prevent the screws from losing. The separately sold color bolt set (model number: GI-305) can also be used for the iPhone 14 series cases, as the bolt size is the same. ※Please note that if you use the aluminum shim to avoid lens contact, the length of the bolts will not be sufficient, and therefore, it cannot be used.
Regarding the Qi wireless charge
It is possible to charge with a Qi wireless charger while using a Solid bumper case (*1)
It will not charge when using a Solid case or an aluminum back panel.
( Please charge with the genuine lighting cable attached with the iPhone)
Regarding the WIFI、3G、4G、Bluetooth、GPS、NFC, etc.
(When an aluminum panel is attached the conditions are the same as the Solid case. )
Face ID → There are no problems while using face recognition and unlocking.
Apple Pay → There are no problem using wifi for both Solid bumper and Solid case. *2
Wifi → There are no problem using wifi for both Solid bumper and Solid case. *2
5G → There are no problem using 4G for both Solid bumper and Solid case. *2
4G → There are no problem using 4G for both Solid bumper and Solid case. *2
Bluetooth → There are no problem using Bluetooth for both Solid bumper and Solid case. *2
GPS → There are no problem using GPS for both Solid bumper and Solid case. *2
Magsafe → There are no problem using GPS for both Solid bumper and Solid case. *2
*1 Using the Qi wireless charger while the case is attached has the possibilities to lower
the charge efficiency due to the 1.5mm thickness of the case that makes a gap between
the wireless charger and the iPhone. Also, there will be a difference on
the charging time depending on the output wattage and the voltage of the adapter the Qi wireless charger.

*2 This product is made of Duralumin, which interrupts the signal from the back of the iPhone.
It is possible that might lower the phone reception.
Using the case in places with a poor reception in the first place can lower the reception of the signal even more. However, there are no problems in places with a good reception.
Color variations
Silver(Back) Silver(Front)
Black(Back) Black(Front)
Red(Back) Red(Front)
Matte purple(Back) Matte purple(Front)
【Size,Weight】
11×83.7×166.5mm / 23g

【Included】
Solid bumper 1set、
Screw 5 pieces(Includes one spare)
Shock absorber 10pieces(Includes two spare)、
Oring 5 pieces(Includes one spare)

【Lens Anti-Touch Kit】 (Packed separately)
7.5-mm Torx screw x 3 pieces (including 1 spare)
2-mm aluminum shim x 3 pieces (including 1 spare)
1-mm aluminum shim x 3 pieces (including 1 spare)
Colors
Please place your order after reading and agreeing with the notes below.

■Due to a tremendous amount of orders it might take 1 to 2 months before we ship the item.

■Your order will be shipped as soon as the product is made.
Lens guard for iPhone 14 Pro / 14 Pro Max
We have also prepared a tungsten steel cut-out lens guard, which will allow you to protect your valuable lens.
Lens guard【Triangle】for 14 Pro / 14 Pro Max
(Color:Silver,Black)
 Lens guard【Square】for 14 Pro / 14 Pro Max
(Color:Black)
Colors
Lens Guard Bar for iPhone 14 Pro Max
We have prepared a lens guard bar for iPhone 14 Pro and 14 Pro Max, whose lens protrudes greatly.
When placed on a flat surface, the lens will not interfere.
(When using the lens guard bar in conjunction with the lens guard, the lens guard will contact first.)

【Please note】
It is not possible to use in conjunction with aluminum color bolts due to insufficient bolt length.
lens guard bar for iPhone 14 Pro Max
(Color:Silver,Black)
Color
Belkin SCREENFORCE iPhone 14 Pro Max Protective Reinforced Glass Film Set of 2
The combination of the Guild design bumper and the Belkin reinforced glass LCD film offers the best clarity and performance.
Cost-effective 2-piece set
【Adopts 9H hardness impact-resistant glass "Japanese AGC Asahi Glass"】
4-layer structure provides the most secure and stronger durability and flexibility.
【Extremely thin 0.33mm glass for higher transparency】
Fingerprint prevention, damage prevention, high transparency, and high touch sensitivity.

【Achieve effortless, precise application with the included "EZ Align Frame"】
Prevent the formation of bubbles and misalignment.
【Notes on Installation】
The side with Tab 1 on the film should be the front side. Please attach the side with Tab 2 on the film to the iPhone.
Belkin SCREENFORCE TemperedGlass
for iPhone 14 Pro Max
Protective Reinforced Glass Film Set of 2
About the protective glass film for iPhone 14 Pro and 14 Pro Max
The solid bumper for iPhone 14 Pro and 14 Pro Max has been improved to have a wider inner width than our previous bumpers, allowing for a wider range of commercially available products to be used. You can use protective glass films that are smaller than the dimensions listed. (Note)

【Note】 ・Even if it is within the dimensions, we do not guarantee that all protective glass films can be mounted due to shape and other limitations. ・Crystal armor and reinforced glass LCD films are larger than our bumpers and cannot be used.
Aluminum color screw set
Colors
※If you choose to use aluminum shims to avoid touching the lens,
the color bolts cannot be used as they are not long enough.
Please place your order after reading and agreeing with the notes below.

■Due to a tremendous amount of orders it might take 1 to 2 months before we ship the item.

■Your order will be shipped as soon as the product is made.
Regarding postage

*For EMS
If the total value of your order is 11,999 yen or less, you will be charged 3,000 yen for shipping.
If the total value of your order is 12,000 yen or more, you will be charged 2,000 yen for shipping.


Please be sure to add your phone number on PayPal when using EMS.
We cannot process the shipping if this information is not included on the invoice.
Please place your order after reading and agreeing with the notes below.

Please read carefully the following before making an order.

We will send a notification regarding the date of delivery individually by email.

The shipment will be in the order as we received them. However, Order colors, and mixed color cases will take time to prepare, this might change the shipping order.

Before making an order please be sure to set your mail to receive messages from info@gilddesign.com.

When the order is complete an auto reply message will be send to you. If you cannot receive the message, please contact info@gilddesign.com after setting the domain.
Warning
・Please understand that we are not responsible for any breakage, or damage that may be caused by actions that were not suggested in this instruction.

・This product is made of Duralumin, which interrupts the signal from the back of the iPhone. It is possible that might lower the phone reception.

・This product is anodized. There are two dots that were not anodized on the inside of the case. These are the electrical connection places that will not catch the color during the anodizing process, and it is not a defect.

・This product is designed for iPhone 14 Pro Max.

・This product is not made to protect the iPhone 14 Pro Max completely from all kinds of damage. Please notice that we will not be responsible for any breakage, loss, damage, or data loss of the iPhone.

・By using silicone shock absorber sheets, our product is designed to prevent the iPhone and the aluminum case from touching each other, and it is not designed to protect the iPhone from all damage.

・Please be aware that our company will not be responsible for any scratches on your iPhone when using the case.

・We might make changes on the case functions, appearance, or package contents without giving a notice.

・There are possibilities that chargers and earphones that are made by companies other than apple cannot be used. (The diameter of the earphone jack is 8.5mm)

・Any protection film under 0.2mm can be used. However, depending on the type of the film there will be possibilities that the film make a gap between it and the screen.

・This case is made of aluminum! Please be careful on the sharp edges when installing the case.

・There is a top and bottom in this product. Please be sure that the circular cut on the case will go to the earphone jack side.

・After putting the wrench firmly into the screw, please fasten it with the right amount of force to prevent the screw from breaking.

・Please note that as the characteristics of anodizing, it is difficult to produce the same color.
There are possibilities that color differs from the image due to the production lot
※iPhone.iPad are trademarks of Apple Inc.
※The trademark'iPhone'is used with a license from Aiphone K.K.