Home/Products/Solid bumper for iPhone 14 / 13 / 13pro
Smooth Our pursuit of usability
Experimenting over and over again we designed this bumper is to have no uncomfortable
feeling between the bumper and the finger.
It is also possible to use the swipe smoothly.
We pursued a case design that would be easy to hold without causing any discomfort when attached to the iPhone
We completed our design after repeated trial manufacturing runs in order to get this just right.
Our cases are designed not to interfere with the operability of any of the iPhone's main functions ―
including the earphone jack, lightning cable, and volume button.
Protect the delicate surface of the lens as much as possible.
The bumper is designed to be slightly taller than
the iPhone's camera lens.
On flat surfaces, the lens will not be damaged
even if you lay it directly on top of it. 		· We also offer an optional lens guard machined from duralumin.
Use to protect your precious lens.
In addition to the Apple genuine MagSafe charger,
numerous third party MagSafe accessories can be attached
to the iPhone without interfering with the Bumper.
※Inside width of Bumper: 65 mm.
※Mount in photo is the Belkin Car Vent Mount.
You can even mount the large-size
Apple genuine Battery Pack directly onto the iPhone.
Our iPhone cases also come equipped with a strap hole.
The strap is connected on the bottom left of the phone,
so it will not interfere with the mouthpiece during phone conversations.
The cases can also be easily stored in your pocket.		 The bumper does not block the antenna module.
There are openings to accommodate each module,
allowing you to use 5G seamlessly.
Rubber o rings are attached to prevent the screws from losing. Available color bolts are the same size and
can be used for iPhone 13 Series cases.
※If you choose to use aluminum shims to avoid touching the lens,
the color bolts cannot be used as they are not long enough.
Regarding the Qi wireless charge
It is possible to charge with a Qi wireless charger while using a Solid bumper case (*1)
It will not charge when using a Solid case or an aluminum back panel.
( Please charge with the genuine lighting cable attached with the iPhone)
Regarding the WIFI、3G、4G、Bluetooth、GPS、NFC, etc.
(When an aluminum panel is attached the conditions are the same as the Solid case. )
Face ID → There are no problems while using face recognition and unlocking.
Apple Pay → There are no problem using wifi for both Solid bumper and Solid case. *2
Wifi → There are no problem using wifi for both Solid bumper and Solid case. *2
5G → There are no problem using 4G for both Solid bumper and Solid case. *2
4G → There are no problem using 4G for both Solid bumper and Solid case. *2
Bluetooth → There are no problem using Bluetooth for both Solid bumper and Solid case. *2
GPS → There are no problem using GPS for both Solid bumper and Solid case. *2
Magsafe → There are no problem using GPS for both Solid bumper and Solid case. *2
*1 Using the Qi wireless charger while the case is attached has the possibilities to lower
the charge efficiency due to the 1.5mm thickness of the case that makes a gap between
the wireless charger and the iPhone. Also, there will be a difference on
the charging time depending on the output wattage and the voltage of the adapter the Qi wireless charger.

*2 This product is made of Duralumin, which interrupts the signal from the back of the iPhone.
It is possible that might lower the phone reception.
Using the case in places with a poor reception in the first place can lower the reception of the signal even more. However, there are no problems in places with a good reception.
Color variations
Silver Black
Red Champagne Gold
Matt Blue
The color is slightly lighter than
the matte blue Solid Bumper for the iPhone 12.		 Matt Pink
【Size,Weight】
11×77×152.5mm、18g

【Included】
Solid bumper 1set、
Screw 5 pieces(Includes one spare)
Shock absorber 10pieces(Includes two spare)、
Oring 5 pieces(Includes one spare)
【Lens Anti-Touch Kit】 (Packed separately)
7.5-mm Torx screw x 3 pieces (including 1 spare)
2-mm aluminum shim x 3 pieces (including 1 spare)
1-mm aluminum shim x 3 pieces (including 1 spare)
Colors
Lens guard for iPhone 13 Pro/13Pro Max
【Triangle】Lens guard for 13Pro / 13Pro Max
Color:Silver,Black
Colors
【Square】Lens guard for 13 Pro/13 Pro Max
Color:Black
Lens guard for iPhone 13 mini/13
【Oval】Lens guard for 13 mini / 13
Color:Silver,Black
Colors
【Square】Lens guard for 13 mini/13
Color:Black
【Oval】Lens guard for iPhone 14 / 14Plus
Color:Silver,Black
Colors
【Square】Lens guard for iPhone 14 / 14Plus
Color:Black
Aluminum color screw set
Colors
※If you choose to use aluminum shims to avoid touching the lens,
the color bolts cannot be used as they are not long enough.
Protective glass film for the iPhone 13 and 13 Pro
The Crystal Armor tempered glass for Solid Bumper for the iPhone 13
and 13 Pro Solid is currently in production.
Production is underway with release projected to begin in 2021.
iPhone 13 Series protective glass film on for back panel
Due to the matte finished glass on the back panel of the iPhone, air bubbles are unavoidable.
We therefore do not plan on making a clear tempered glass protective film.
As soon as we find a suitable commercial product,
we will announce it on our website and our official social media accounts.
Precaution about front and back tempered glass protectors from retailers

GILD design makes no guarantee about compatibility as long as the thickness is 0.2 mm or less. Please be aware of this before purchasing. Other than the products that our company recommends, front and back tempered glass that are 0.2mm or less in thickness should be compatible. However, even if they are 0.2mm or less, the installation method and glass type may cause some air bubble infiltration and defects like bulging. We cannot guarantee that it will definitely be compatible as long as the thickness is 0.2mm or less. Please be aware of this before you purchase.
Regarding postage

*For EMS
If the total value of your order is 11,999 yen or less, you will be charged 3,000 yen for shipping.
If the total value of your order is 12,000 yen or more, you will be charged 2,000 yen for shipping.


Please be sure to add your phone number on PayPal when using EMS.
We cannot process the shipping if this information is not included on the invoice.
Please place your order after reading and agreeing with the notes below.

Please read carefully the following before making an order.

We will send a notification regarding the date of delivery individually by email.

The shipment will be in the order as we received them. However, Order colors, and mixed color cases will take time to prepare, this might change the shipping order.

Before making an order please be sure to set your mail to receive messages from info@gilddesign.com.

When the order is complete an auto reply message will be send to you. If you cannot receive the message, please contact info@gilddesign.com after setting the domain.
Warning
・Please understand that we are not responsible for any breakage, or damage that may be caused by actions that were not suggested in this instruction.

・This product is made of Duralumin, which interrupts the signal from the back of the iPhone. It is possible that might lower the phone reception.

・This product is anodized. There are two dots that were not anodized on the inside of the case. These are the electrical connection places that will not catch the color during the anodizing process, and it is not a defect.

・This product is designed for iPhone 14 / 13 / 13pro.

・This product is not made to protect the iPhone 14 / 13 / 13pro completely from all kinds of damage. Please notice that we will not be responsible for any breakage, loss, damage, or data loss of the iPhone.

・By using silicone shock absorber sheets, our product is designed to prevent the iPhone and the aluminum case from touching each other, and it is not designed to protect the iPhone from all damage.

・Please be aware that our company will not be responsible for any scratches on your iPhone when using the case.

・We might make changes on the case functions, appearance, or package contents without giving a notice.

・There are possibilities that chargers and earphones that are made by companies other than apple cannot be used. (The diameter of the earphone jack is 8.5mm)

・Any protection film under 0.2mm can be used. However, depending on the type of the film there will be possibilities that the film make a gap between it and the screen.

・This case is made of aluminum! Please be careful on the sharp edges when installing the case.

・There is a top and bottom in this product. Please be sure that the circular cut on the case will go to the earphone jack side.

・After putting the wrench firmly into the screw, please fasten it with the right amount of force to prevent the screw from breaking.

・Please note that as the characteristics of anodizing, it is difficult to produce the same color.
There are possibilities that color differs from the image due to the production lot
※iPhone.iPad are trademarks of Apple Inc.
※The trademark'iPhone'is used with a license from Aiphone K.K.